Crocodile Glass Block Tile Grout/White


In stock

SKU: C02091001 Category: Tag:

ប្រើសំរាប់ភ្ជាប់រ៉ង Class Block ទប់ស្កាតការកើតស្នឹមខ្មៅ(បន្ថែមទំហំចន្លោះ)

Crocodile Glass Block

  • បន្ថែមកម្លាំងស្អិតជាប់ខ្លាំង ល្អប្រសើរ មិនរបករឺរបើក មិនប្រេះស្រាំសូម្បីចន្លោះរ៉ងធំទប់ស្កាតស្នឹមខ្មៅនិងដុសស្លែដោយសារធាតុ Microban កាត់បន្ថយស្នាមប្រឡាក់កប់ជ្រៅដោយសារធាតុ Hyropphobic
  • មានពណ៌ស្រស់ស្អាតច្រើនពណ៌

ចន្លោះរ៉ង : 8-15 ម.ម
ស្ដងដាអាមេរិច : ANSI A 118.6(Sanded) A 118.7(sanded)
ចំណុះ : 1 គ.ក


Type Glass Block Tile Grout
American standard ANSI A 118.3 (Sanded), A 118.7 (Sanded)
European standard EN13888 CG2
Product color 10 shades
Packing size 1 kg / bag

How to use

Crocodile sealant glass block for glass block grout, especially with sand mixture Portland cement Specialty chemicals and colors So it does not peel off, does not shrink, has no bad smell Not harmful to users And have special ingredients as follows: micro-flat, hydrophobic, special binder, extra-bond and others which enhance the protective properties to inhibit the growth of black fungus Prevent water seepage And increase the adhesion strength, thus helping to have high adhesion and long service life Suitable for grooves that require grout not more than 8-15 mm. Can be used for external work. Within the area requires special cleanliness And is a mixed product, just add water and mix well, can be used immediately Instructions for use The grout width must not exceed 8-15 mm. The groove depth should not be less than 2/3 of the tile thickness. The grout must be done after 48 hours or after the curing adhesive cement is complete. Surface preparation Clean the grout grooves to be free from dust, dirt, debris, and prevent water from getting trapped before grout. Mixture ratio 1 kg glass block grout (1 bag) per 0.25 liters of water or 3 glass block grout glue per 1 part water by volume Mixing

  • Pour the grout glue into the water. While turning the mixer around low or stirring well
  • Leave it for about 5 minutes to allow the chemical to curing. And stir again before using While in use should be periodically stirred
  • When the adhesive is thick, because it is too long or too long Do not add water to make it liquid. Should be discarded and mixed again


  1. Use a rubber screed trowel that is well blended to fill the groove. By making a oblique angle and groove to prevent the rubber trowel from pulling the grout out of the groove Use the trowel to scrape off the surface of the tile as much as possible.
  2. Leave until the grout glue begins to incubate. So use a cloth or sponge moistened with water and wring thoroughly Then use a dry cloth to wipe the surface of the tile again

Curing and grouting for the first 72 hours should use sticky paper. (Brown paper used to make bags or wrappers) to help seal the glue gradually curing and help prevent dust or other dirt Stick to the surface of the grout that has not dried Do not use plastic or newspaper paper instead of sticky paper.  Cleaning after 10 days should clean the tile surface one more time to allow the glue grout that may be left out of the tile surface. By using soapy water mixed with warm water to pour all over Leave for a while Therefore wipe clean Do not use concentrated solutions or acids. Because it will erode the grout and cause the color of the drug to change

  • If necessary, use diluted acids or crocodile cleaners to clean the grout grooves. But should test in a small area first
  • The use of a polish remover or stain remover should be done after the curing glue is completely cured. Which must not be less than 30 days and should be tested in a small area first


  • Should not be used with areas that are exposed to acids all the time
  • Cement may cause skin irritation. Should use various safety equipment such as gloves, dust masks, goggles
  • In case of eye contact, rinse the eyes with clean water several times immediately. And consult a doctor
  • If being exposed or exposed to the skin Use clean water and soap.
  • Should be kept out of the reach of children

Storage should be kept in the shade. Which has good ventilation The area must be dry, not damp because it causes the product to not deteriorate. Product life is 1 year from the date of manufacture. In unopened condition (If not used, the bag must be tightly sealed every time)

Submit your review

Your email address will not be published. Required fields are marked *


There are no reviews yet.